Search results for "Conversion coating"

Corrosion protection of Nd–Fe–B type permanent magnets by zinc phosphate surface conversion coatings

2001

Abstract The use of protective zinc phosphate top coatings to protect Nd–Fe–B type permanent magnets against corrosion is discussed. The progress of the phosphatisation process has been tested by simultaneous measurement of pH near surface, corrosion potential, substrate mass loss and phosphate coating mass gain. The corrosion behaviour of the magnet in phosphate solution was analyzed by the anodic polarization technique and the general resistance of the magnet to corrosion was evaluated by the Akimov drop test. It is shown that immersion of the magnet in the acidified (pH=2) phosphating solution containing Zn(II), nitrate and fluoride ions resulted in the formation of well adhered, thin an…

2017

Abstract Chromic acid anodizing is important for the corrosion protection of aerospace aluminium alloys. Previous study has demonstrated that SO 4 2 − impurity in the chromic acid affects the film growth on aluminium at a voltage of 100 V. The present work further investigates aluminium and extends the study to industrial anodizing conditions (Bengough-Stuart (B-S) process) and to the AA 2024-T3 alloy. It is shown that SO 4 2 − concentrations between ~ 38–300 ppm reduce the film growth rate for aluminium anodized at 100 V in comparison with an electrolyte than contains ≤ 1.5 ppm SO 4 2 − , whereas ~ 1500–3000 ppm SO 4 2 have an opposite effect and lead to an unstable pore diameter. Under th…

A photoelectrochemical investigation of conversion coatings on Mg substrates

2005

Abstract The structure, morphology and composition of conversion coatings grown in stannate bath on pure Mg were studied using potential–time, polarization curves, X-ray diffraction, scanning electron microscopy and photocurrent spectroscopy. The coating is manly constituted by crystalline magnesium–tin hydroxide, whose morphology and distribution depends on the conversion bath composition and temperature. The photoelectrochemical investigation allowed to estimate the band gap value of MgSn(OH) 6 and flat band potential. A sketch of the metal/passive film/electrolyte junction formed during conversion on the metal substrate is reported to account for the overall photoelectrochemical behaviou…

Study of the Chemical Conversion of Aluminum Alloys by Coupling CFDE and EQCM

2004

The ability of the channel flow double electrode (CFDE) technique and electrochemical quartz crystal microbalance (EQCM) for studying in situ chromate phosphate conversion coating on 5182 aluminum alloys was explored. It was first demonstrated that aqueous Cr(VI) can be analyzed quantitatively with the CFDE technique by reduction into Cr(III) on a graphite electrode. Samples used for EQCM were quartz plated by physical vapor deposition using a 5182 alloy target, allowing thin layers of aluminum alloys with a similar chemical composition to be obtained. EQCM was adapted in order to account for the hydrodynamic conditions in an industrial process, by placing the quartz in a flow cell. In orde…

Structural Analysis and Photocurrent Spectroscopy of CCCs on 99.99% Aluminum

2003

A characterization of chromate conversion coatings (CCCs) formed in the presence and in the absence of accelerator (ferroferricyanide redox couple) has been performed by various techniques (transmission electron microscopy, TEM, glow discharge optical emission spectrometry, GDOES, X-ray absorption near-end structure, XANES, and photon correlation spectroscopy). The results of a detailed investigation on morphological, compositional, and solid-state properties of freshly converted aluminum samples at different immersion times (30 s-90 min) are reported. The TEM and GDOES data suggest the presence of iron-cyanide species only in the external layer of CCC of nearly constant thickness. The XANE…

Improvement of the electrochemical behaviour of Zn-electroplated steel using regenerated Cr(III) passivation baths

2014

[EN] Conversion coatings based on trivalent chromium are more sensitive to the presence of zinc and iron impurities than the chromate formulations. This fact contributes to a decrease in the quality of passivation and to the generation of a significant amount of hazardous liquid waste. Recently, a new eco-innovative process based on Emulsion Pertraction Technology (EPT) is being implemented at industrial scale for selectively removing Zn and Fe from spent passivation baths in order to enhance the lifetime of the Cr (III) baths. In this study, the effect of Zn and Fe removal on the electrochemical behaviour of Zn-electroplated steel samples was evaluated by means of polarisation curves and e…

Two-Dimensional Assembling of (2,2‘-Bipyrimidine)bis(oxalato)chromate(III) Units through Alkaline Cations

1999

Self-assembling of the tris-chelated [Cr(bpm)(ox)2]- complex with Na+ in aqueous solution leads to the remarkable bimetallic honeycomb layered compound of formula [NaICrIII(bpm)(ox)2]·5H2O (2) (bpm...

Magnetic and magneto-optical properties of nickel hexacyanoferrate/chromate thin films

2017

One of the most important challenges of modern science and technology is the quest for novel and tuneable materials, the properties of which can be widely controlled by chemical modifications or external stimuli. Simultaneously, an interest in the development of magnetic thin films also gains significant attention. In the current paper we bring together both these challenges and present a study of a new type of low-dimensional nickel hexacyanoferrate/chromate system. Thin films were obtained by the "layer by layer" deposition technique, where the ratio of Fe/Cr was controlled by the dipping sequence. The scope of this work is a comprehensive analysis of structural, spectroscopic and magneti…

The generalized H-point standard-additions method to determine analytes present in two different chemical forms in unknown matrix samples. Part II. C…

2000

The generalized H-point standard-additions method (GHPSAM) is used in order to obtain the total Cr(VI) and chromate concentration in water samples whose matrices are completely unknown. Moreover, a new methodology, which is a modification of the GHPSAM, is proposed for the simultaneous determination of the two major chemical forms of Cr(VI) present in the sample. The method is based on the location of spectral intervals where the behaviour of the interferent absorbance can be considered as linear. From these intervals, the analyte concentration free from bias error can be estimated. Spiked samples of dig and harbour water measured in the UV–visible spectral region have been tested to check …

Inhibition Probing on a Cut-Edge Electrode Machined from a Primer-Coated 2024-T3 Alloy

2013

Conventional corrosion protection of 2024-T3 alloys (AA2024T3) in aeronautic structures combines conversion coating with chromate-inhibited primer protected by a top-coat. In some cases this protection can break down after mechanical damage to the paint systems inducing a risk of localized corrosion if the release of inhibitors trapped in the primer does not reach a critical level. There is a need for developing computational models combining the inhibitor release and transport within and from the coating system andthecorrosioninhibitionprocess,toassistinthedesignofnewmultifunctionalcoatingsystems.Theinfluenceonthecorrosioninhibition of various parameters such inhibitor release rate, defect…